National Semiconductor | High-performance Analog

 

 LM2753   

High Power Switched Capacitor Voltage Convertor/Flash LED Driver
Click link to Download

Features
  • Input Voltage Range: 3.0V to 5.5V
  • Regulated 5V Output
  • 250mA Output Current with a 3.6V input
  • 400mA Pulsed Output Current (up to 500ms duration)
  • 60µA (typ.) Quiescent Current
  • PFM Regulation
  • Inductor-less solution: requires only 3 small capacitors
  • <1µA Typical Shutdown Current
  • 10-pin LLP Package (No Pullback):
    3mm x 3mm x 0.8mm
  • Description

    The LM2753 is capable of driving a Flash LED with a pulsed current of 400mA at an input voltage of 3.6V. A switched capacitor doubler, the LM2753 provides a regulated 5V output (VOUT) over an input supply range of 3.0V to 5.5V. The switched output, IOUT, takes less than 10ns to turn on and provide maximum current to a Flash LED. Flash LED current is set via a ballast resistor. Continuous illumination current (Torch Mode) is programmed by connecting a resistor between IOUT and VOUT. This device uses only three small, low-cost ceramic capacitors.

    LM2753 uses Pulse Frequency Modulation (PFM) regulation. Typical operating frequency is 725kHz. Under no-load conditions, LM2753 operates on only 60µA. If the output is connected to ground, the charge pump stays in the gain of 1 which helps limit the input current to 300mA (typ.)

    LM2753 is available in a 10-pin No Pullback Leadless Leadframe Package: LLP-10.


    Applications

  • Cell Phone Camera Flash
  • General Purpose Regulated Voltage Output, High Current Supply



  • Typical Application
    click for larger image


    Block Diagram
    click for larger image



    Typical Performance
    click for larger image


     

    ParametersValues
    Switch Current 0.4 Amp
    Output Min 5 Volt
    Output Max 5 Volt
    Input Min Voltage 3 Volt
    Input Max Voltage 5.5 Volt
    Efficiency (peak) 68 %
    Frequency Min 725 kHz
    Frequency Max 725 kHz
    Special Features Flash-LED driver, 250mA continuous load and 400mA pulsed load
    Adj Switch Frequency No
    Adjustable Output No
    On/Off Pin Yes
    PWM Mode PFM Switched Capacitor Doubler
    Topology Boost
    Step-Up Yes
    Inverting No
    RegType Switched Cap Regulator
    Temperature Min -40 deg C
    Temperature Max 85 deg C
    PowerWise No

    Datasheets
    TitleSizeDateOther
    Language
    LM2753 High Power Switched Capacitor Voltage Convertor/Flash LED Driver1177
    Kbytes
    10-Mar-07   

    Part Number(s)
    (NSID)
    Top ViewAvailabilityCurrent Reported StockBudgetary PricingPack
    Size
    LM2753SD/NOPB

    LM2753SD

    RoHS Status


    LLP
    Full production
    Lead Time: 6 weeks

     
    DistributorRegionQty
    DIGI-KEYWorldwide1081
    FARNELLEurope and Asia960
    MOUSERWorldwide994
    NEWARKAmericas960
    RS COMPONENTSWorldwide10
    $0.76 each at 1K+ pcsreel
    of
    1000
    LM2753SDX/NOPB

    LM2753SDX

    RoHS Status


    LLP
    Full production
    Lead Time: 6 weeks

     
    DistributorRegionQty
    DIGI-KEYWorldwide0
    $0.76 each at 1K+ pcsreel
    of
    4500

    All information pertaining to the RoHS Compliance Standard can be found at http://www.national.com/en/packaging/leadfree.html.

    Moisture Sensitivity Level Data for LM2753.

    A RoHS compliance or an IPC 1752 report can be acquired at http://www.national.com/en/packaging/greennopb.html.

    National's certificate of product compliance for LM2753 is located at RoHS Status.

    Part Number(s)
    (NSID)
    Weight
    (milligrams)
    TypePinsMSL RatingPeak ReflowRoHS
    Status
    CAD SymbolsModelsPackage
    Marking
    Format
    LM2753SD/NOPB

    LM2753SD
    21.112
    21.182
    LLP101
    1
    260
    260
    DetailDownloadN/A
    ZXYTT
    D004B
    LM2753SDX/NOPB

    LM2753SDX
    21.112
    21.182
    LLP101
    1
    260
    260
    DetailDownloadN/A
    ZXYTT
    D004B

    All information pertaining to the RoHS Compliance Standard can be found at http://www.national.com/en/packaging/leadfree.html.

    Moisture Sensitivity Level Data for LM2753.

    A RoHS compliance or an IPC 1752 report can be acquired at http://www.national.com/en/packaging/greennopb.html.

    National's certificate of product compliance for LM2753 is located at RoHS Status.

    CAD Symbols and Models
    Download LM2753 CAD Symbols
     Models
    N/A


    Reliability Metrics
    Part Number Process EFR Reject EFR Sample Size PPM LTA Rejects LTA Device Hours FITS MTTF (Hours)
    LM2753SDCMOS70213010015840003449464325
    LM2753SDXCMOS70213010015840003449464325

    Note: The Early Failure Rates (EFR) were calculated as point estimate PPM based on rejects and sample size for EFR. The Long Term Failure Rates were calculated at 60% confidence using the Arrhenius equation at 0.7eV activation energy and derating the assumed stress temperature of 150°C to an application temperature of 55°C.

    For more information on Reliability Metrics, please click here.


    All information pertaining to the RoHS Compliance Standard can be found at http://www.national.com/en/packaging/leadfree.html.

    Moisture Sensitivity Level Data for LM2753.

    A RoHS compliance or an IPC 1752 report can be acquired at http://www.national.com/en/packaging/greennopb.html.

    National's certificate of product compliance for LM2753 is located at RoHS Status.

    [Information as of 9-Feb-2012]