| Title |
Author |
Publication |
Publication Date |
| Sensor signal conditioning need not be difficult (Part 1 / Part 2) |
Nicholas Gray |
Planet Analog |
10/09 |
| A new set of Sallen-Key filter equations |
Martin Cano |
EDN |
10/09 |
| Build a bidirectional, single-wire, line-powered transceiver using just a few basic parts |
Donald Schelle |
Planet Analog |
8/09 |
| Designing a Second-Order Anti-aliasing Filter for a Sensor Signal Path |
Bob Hennink |
Sensors Magazine |
8/09 |
| Use Current-Feedback Amplifiers to Speed Up Data-Acquisition and High-End Video Systems |
Loren Siebert |
Planet Analog |
6/09 |
| HD Component Video Over CAT5 Cable Using Current Feedback Amplifiers |
Vannavong Philavanh |
Video/Imaging DesignWire |
6/09 |
|
Filter Component Considerations in Precision Signal-Conversion Applications
|
Daniel Burton |
Planet Analog (registration required) |
6/09 |
| Eliminate Sallen-Key Stopband Leakage with a Voltage Follower |
Martin Cano |
EDN |
5/09 |
|
Noise in Chopper-Stabilized Amplifier Applications--design tradeoffs and how to minimize noise in these circuits
|
Walter Bacharowski |
Electronic Products |
4/09 |
| Oscillator Delivers Four Multi-Phased, Equal-Amplitude Sine Waves |
John Guy |
Electronic Design |
3/09 |
| Taking the Mystery out of Gigahertz, Gigasample & Gigabit Systems Design |
Paul McCormack |
Embedded.com |
12/08 |
| Techniques to enhance op amp signal integrity in low-level sensor applications (4-part article) |
Jerry Freeman |
Planet Analog |
12/08 |
| Provide a Negative Bias Voltage to Low-voltage Amplifiers to Improve their Near-zero-volt Performance |
Walter Bacharowski |
Planet Analog & EE Times |
11/08 |
| Interface High-Performance Op Amps With ADCs |
Maithil Pachchigar |
Electronic Design |
9/08 |
| EMI Susceptibility in Analog Circuits |
Walter Bacharowski |
WirelessZONE |
8/08 |
| VIP50 Operational Amplifier for Medical Portable Diagnosis Equipment |
Carine Alberti |
Electronic Science Korea |
6/08 |
| Thermopiles Raise Heat on Gas Detection |
Carine Alberti |
Electronic Product Design |
6/08 |
| Signal Conditioning in Portable Medical Applications |
Carine Alberti |
Electronic Product News |
5/08 |
| Interfacing High-speed Data Converters |
Hooman Hashemi |
EDN |
4/08 |
| Understanding precision comparator applications (2-part article) |
Walter Bacharowski |
Planet Analog |
3/08 |
| Noise Assessment via Pspice Analysis System |
Hooman Hashemi |
Eepw.com.cn |
3/08 |
| Compensation techniques for driving large-capacitance loads with high-speed amplifiers |
Maithil Pachchigar |
Planet Analog |
2/08 |
| Decompensating Amplifiers Improve Performance |
Walter Bacharowski |
EDN |
12/07 |
| Selecting Amplifiers and ADCs For High Performance Signal Paths |
Mike Ewer |
Electronic Parts & Components (Korea) |
12/07 |
| Design Migration from the LM1881 to the LMH1980 |
Alan Ocampo |
Elektronik Industrie Application Guide (Europe) |
11/07 |
| Improving CMRR in CAT-5 video links and other differential video transmitter-receiver applications |
Maithil Pachchigar |
Video/Imaging DesignLine |
10/07 |
| Using a strain-gauge transducer in a Wheatstone-bridge configuration |
Janhavi Desai |
Planet Analog |
10/07 |
| Preventative Maintenance Systems Are Important |
Walter Bacharowski |
elektrotechnik.de (Germany) |
10/07 |
| Use in-the-loop gain control to extend dynamic range |
Loren Siebert |
RF DesignLine |
9/07 |
| Measuring composite-video signal performance requires understanding differential gain and phase(2-part article) |
Cliff Win, Jr. |
Planet Analog |
8/07 |
| Understand and apply the transimpedance amplifier (2-part article) |
David Westerman |
RF DesignLine |
8/07 |
| How Much Load Can Your Operational Amplifier Drive? |
Hooman Hashemi |
Planet Analog |
2/07 |
| Back to the Basics: Using Current-Feedback Op Amps for High-speed Designs |
Loren Siebert |
Embedded.com |
1/07 |
| Trends in video ICs |
Tushar Patel |
Electronic Products |
10/06 |
| Gain error affects op amp choices |
Soufiane Bendaoud |
Planet Analog |
7/06 |
| Use PSpice models to estimate amplifier noise |
Hooman Hashemi |
Planet Analog |
2/06 |
| Basics of Design: Take The Right Steps To Achieve Accurate Measurements (pdf 418KB) |
Don Tuite, ED Online |
Electronic Design |
3/05 |
